Hey guys, I'm thinking about replacing the Idler pulley bearing on my 84 turbo. Rock auto has two sizes available..which do I get?
| Attachments: |
|
Screen Shot 2013-04-29 at 11.48.50 PM 1.png [ 37.5 KiB | Viewed 8412 times ] |
| CTZCC.COM http://forums.ctzcc.com/ |
|
| Z31 Idler Pulley Bearing http://forums.ctzcc.com/viewtopic.php?f=4&t=7479 |
Page 1 of 1 |
| Author: | Filipe [ Wed May 01, 2013 6:39 am ] | ||
| Post subject: | Z31 Idler Pulley Bearing | ||
Hey guys, I'm thinking about replacing the Idler pulley bearing on my 84 turbo. Rock auto has two sizes available..which do I get?
|
|||
| Author: | Frank T [ Wed May 01, 2013 9:26 am ] |
| Post subject: | |
Which one was made later? One was an improvement over the original, I would think.......? |
|
| Author: | Paul [ Wed May 01, 2013 12:39 pm ] |
| Post subject: | |
Did you click on the PT # to see the application? Turbo? N/A? or year change? Could always measure yours to see what size you have. |
|
| Author: | Filipe [ Wed May 01, 2013 4:48 pm ] |
| Post subject: | |
Both are for turbos, 84. Or that's what they're listed under at least.. I might have to measure it...going to try to without taking it out. |
|
| Author: | mikeatrpi [ Thu May 02, 2013 3:41 pm ] |
| Post subject: | |
Take it out of the car and clean it up. Usually there is a number on it somewhere - 6204 or something like that. You can buy them locally if you go by that number at places like Napa, Levine or CarQuest. |
|
| Author: | Filipe [ Thu May 02, 2013 4:54 pm ] |
| Post subject: | |
Wish I had seen this earlier...I took a measurement of it last night and I think I got the right one...if not, I'll definitely look for that part number! Thanks! |
|
| Author: | mikeatrpi [ Thu May 02, 2013 8:57 pm ] |
| Post subject: | |
I checked my notes - on my 82 280zx, the old bearing said "6203" and I replaced it with a carquest "203-FF" bearing. |
|
| Author: | Paul [ Fri May 03, 2013 12:05 pm ] |
| Post subject: | |
For one, are you talking about the timing belt, because there is only the tensioner pulley? Or are you talking about one of the drive belt pulleys? |
|
| Author: | jtang [ Fri May 03, 2013 6:26 pm ] |
| Post subject: | |
I think this is the one that is on the serpentine belt (the one for the air conditioning and it goes to the "idler"), so no, not the timing belt. |
|
| Author: | Filipe [ Sun May 05, 2013 7:08 am ] |
| Post subject: | |
Yup, Justin is right. |
|
| Author: | Paul [ Mon May 06, 2013 8:26 am ] |
| Post subject: | |
Ahh, got it. I call those adjusting Pulleys for the belt. |
|
| Author: | Gregmatic [ Mon May 06, 2013 9:32 am ] |
| Post subject: | |
Fillipe, Just saw this post. I tried the same thing you are attempting to do and ended up ordering both Beck-Arnley bearings from Rockauto as I was unsure of which size to get. Sad to say but neither one fit any of my tensioner pulleys. Maybe your luck will be better... |
|
| Author: | Filipe [ Mon Jul 29, 2013 11:02 am ] |
| Post subject: | |
Yeah Greg, I ordered a Beck Arnley as well, didn't fit either. Oh well. |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|